First config file checkin
This commit is contained in:
171
config/printer.cfg
Normal file
171
config/printer.cfg
Normal file
@@ -0,0 +1,171 @@
|
||||
# This file contains common pin mappings for the 2018 Creality
|
||||
# Ender 3. To use this config, the firmware should be compiled for the
|
||||
# AVR atmega1284p.
|
||||
|
||||
# Note, a number of Melzi boards are shipped with a bootloader that
|
||||
# requires the following command to flash the board:
|
||||
# avrdude -p atmega1284p -c arduino -b 57600 -P /dev/ttyUSB0 -U out/klipper.elf.hex
|
||||
# If the above command does not work and "make flash" does not work
|
||||
# then one may need to flash a bootloader to the board - see the
|
||||
# Klipper docs/Bootloaders.md file for more information.
|
||||
|
||||
[include mainsail.cfg]
|
||||
|
||||
[include scottc.cfg]
|
||||
|
||||
# See docs/Config_Reference.md for a description of parameters.
|
||||
|
||||
[stepper_x]
|
||||
step_pin: PD7
|
||||
dir_pin: !PC5
|
||||
enable_pin: !PD6
|
||||
microsteps: 16
|
||||
rotation_distance: 40
|
||||
endstop_pin: ^PC2
|
||||
position_endstop: 0
|
||||
position_max: 235
|
||||
homing_speed: 50
|
||||
|
||||
[stepper_y]
|
||||
step_pin: PC6
|
||||
dir_pin: !PC7
|
||||
enable_pin: !PD6
|
||||
microsteps: 16
|
||||
rotation_distance: 40
|
||||
endstop_pin: ^PC3
|
||||
position_endstop: 0
|
||||
position_max: 235
|
||||
homing_speed: 50
|
||||
|
||||
[stepper_z]
|
||||
step_pin: PB3
|
||||
dir_pin: PB2
|
||||
enable_pin: !PA5
|
||||
microsteps: 16
|
||||
rotation_distance: 8
|
||||
endstop_pin: probe:z_virtual_endstop
|
||||
position_max: 250
|
||||
|
||||
[extruder]
|
||||
max_extrude_only_distance: 100.0
|
||||
step_pin: PB1
|
||||
dir_pin: !PB0
|
||||
enable_pin: !PD6
|
||||
microsteps: 16
|
||||
rotation_distance: 23.046
|
||||
nozzle_diameter: 0.600
|
||||
filament_diameter: 1.750
|
||||
heater_pin: PD5
|
||||
sensor_type: EPCOS 100K B57560G104F
|
||||
sensor_pin: PA7
|
||||
min_temp: 0
|
||||
max_temp: 250
|
||||
|
||||
[heater_bed]
|
||||
heater_pin: PD4
|
||||
sensor_type: EPCOS 100K B57560G104F
|
||||
sensor_pin: PA6
|
||||
min_temp: 0
|
||||
max_temp: 80
|
||||
|
||||
[fan]
|
||||
pin: PB4
|
||||
|
||||
[mcu]
|
||||
serial: /dev/serial/by-id/usb-1a86_USB2.0-Serial-if00-port0
|
||||
baud: 250000
|
||||
|
||||
[printer]
|
||||
kinematics: cartesian
|
||||
max_velocity: 300
|
||||
max_accel: 3000
|
||||
max_z_velocity: 5
|
||||
max_z_accel: 100
|
||||
|
||||
[bed_screws]
|
||||
screw1: 30.5, 37
|
||||
screw2: 30.5, 207
|
||||
screw3: 204.5, 207
|
||||
screw4: 204.5, 37
|
||||
|
||||
[display]
|
||||
lcd_type: st7920
|
||||
cs_pin: PA3
|
||||
sclk_pin: PA1
|
||||
sid_pin: PC1
|
||||
encoder_pins: ^PD2, ^PD3
|
||||
click_pin: ^!PC0
|
||||
|
||||
# The print bed can move so far to the front, that the nozzle can reach the
|
||||
# plastic cover of the print bed heater cable (only when the bed is moved by
|
||||
# hand). By homing the Y axis before the X axis, it is ensured the nozzle will
|
||||
# not melt through the plastic part.
|
||||
# BEWARE: You will lose the ability to home axes individually. The printer will
|
||||
# always home all axes for every G28 command.
|
||||
#[homing_override]
|
||||
#gcode:
|
||||
# G28 Y0
|
||||
# G28 X0
|
||||
# G28 Z0
|
||||
|
||||
[bltouch]
|
||||
sensor_pin: ^PC4
|
||||
control_pin: PA4
|
||||
x_offset: -40.00
|
||||
y_offset: -8.00
|
||||
z_offset: 2.60
|
||||
|
||||
[safe_z_home]
|
||||
home_xy_position: 162, 125 # Change coordinates to the center of your print bed
|
||||
speed: 50
|
||||
z_hop: 10 # Move up 10mm
|
||||
z_hop_speed: 5
|
||||
|
||||
[bed_mesh]
|
||||
speed: 120
|
||||
horizontal_move_z: 5
|
||||
mesh_min: 20, 20
|
||||
mesh_max: 195, 220
|
||||
mesh_pps: 2, 2
|
||||
probe_count: 8,8
|
||||
algorithm: bicubic
|
||||
fade_start: 1
|
||||
fade_end: 10
|
||||
fade_target: 0
|
||||
|
||||
#*# <---------------------- SAVE_CONFIG ---------------------->
|
||||
#*# DO NOT EDIT THIS BLOCK OR BELOW. The contents are auto-generated.
|
||||
#*#
|
||||
#*# [heater_bed]
|
||||
#*# control = pid
|
||||
#*# pid_kp = 64.222
|
||||
#*# pid_ki = 1.278
|
||||
#*# pid_kd = 806.790
|
||||
#*#
|
||||
#*# [extruder]
|
||||
#*# control = pid
|
||||
#*# pid_kp = 26.561
|
||||
#*# pid_ki = 1.476
|
||||
#*# pid_kd = 119.524
|
||||
#*#
|
||||
#*# [bed_mesh default]
|
||||
#*# version = 1
|
||||
#*# points =
|
||||
#*# 0.027500, 0.022500, -0.012500, -0.017500, -0.042500, -0.050000, -0.047500, -0.035000
|
||||
#*# 0.062500, 0.047500, 0.015000, 0.010000, -0.022500, -0.030000, -0.027500, -0.037500
|
||||
#*# 0.110000, 0.100000, 0.050000, 0.037500, -0.010000, -0.022500, -0.027500, -0.035000
|
||||
#*# 0.117500, 0.105000, 0.065000, 0.037500, 0.000000, -0.007500, -0.022500, -0.022500
|
||||
#*# 0.132500, 0.112500, 0.072500, 0.055000, 0.017500, -0.007500, -0.017500, -0.025000
|
||||
#*# 0.152500, 0.125000, 0.087500, 0.060000, 0.025000, 0.005000, -0.002500, -0.010000
|
||||
#*# 0.105000, 0.102500, 0.062500, 0.045000, 0.022500, 0.015000, 0.015000, 0.025000
|
||||
#*# 0.100000, 0.087500, 0.055000, 0.055000, 0.032500, 0.025000, 0.037500, 0.035000
|
||||
#*# x_count = 8
|
||||
#*# y_count = 8
|
||||
#*# mesh_x_pps = 2
|
||||
#*# mesh_y_pps = 2
|
||||
#*# algo = bicubic
|
||||
#*# tension = 0.2
|
||||
#*# min_x = 20.0
|
||||
#*# max_x = 195.0
|
||||
#*# min_y = 20.0
|
||||
#*# max_y = 219.99
|
||||
Reference in New Issue
Block a user