Initial config

boot/cmdline.txt

@@ -0,0 +1 @@
+console=tty1 console=serial0,115200 root=PARTUUID=1ace4a06-02 rootfstype=ext4 fsck.repair=yes rootwait cfg80211.ieee80211_regdom=GB

boot/config.txt

@@ -0,0 +1,151 @@
+# For more options and information see
+# http://rpf.io/configtxt
+# Some settings may impact device functionality. See link above for details
+
+# uncomment if you get no picture on HDMI for a default "safe" mode
+#hdmi_safe=1
+
+# uncomment the following to adjust overscan. Use positive numbers if console
+# goes off screen, and negative if there is too much border
+#overscan_left=16
+#overscan_right=16
+#overscan_top=16
+#overscan_bottom=16
+
+# uncomment to force a console size. By default it will be display's size minus
+# overscan.
+#framebuffer_width=1280
+#framebuffer_height=720
+
+# uncomment if hdmi display is not detected and composite is being output
+#hdmi_force_hotplug=1
+
+# uncomment to force a specific HDMI mode (this will force VGA)
+#hdmi_group=1
+#hdmi_mode=1
+
+# uncomment to force a HDMI mode rather than DVI. This can make audio work in
+# DMT (computer monitor) modes
+#hdmi_drive=2
+
+# uncomment to increase signal to HDMI, if you have interference, blanking, or
+# no display
+#config_hdmi_boost=4
+
+# uncomment for composite PAL
+#sdtv_mode=2
+
+#uncomment to overclock the arm. 700 MHz is the default.
+#arm_freq=800
+
+# Uncomment some or all of these to enable the optional hardware interfaces
+dtparam=i2c_arm=on
+#dtparam=i2s=on
+dtparam=spi=on
+
+# Uncomment this to enable infrared communication.
+#dtoverlay=gpio-ir,gpio_pin=17
+#dtoverlay=gpio-ir-tx,gpio_pin=18
+
+# Additional overlays and parameters are documented /boot/overlays/README
+
+# Enable audio (loads snd_bcm2835)
+dtparam=audio=off
+
+# Automatically load overlays for detected cameras
+start_x=1
+
+# Automatically load overlays for detected DSI displays
+display_auto_detect=1
+
+# Enable DRM VC4 V3D driver
+#dtoverlay=vc4-kms-v3d
+#dtoverlay=vc4-kms-v3d,cma-128
+max_framebuffers=2
+
+# Run in 64-bit mode
+arm_64bit=1
+
+# Disable compensation for displays with overscan
+disable_overscan=1
+
+[cm4]
+# Enable host mode on the 2711 built-in XHCI USB controller.
+# This line should be removed if the legacy DWC2 controller is required
+# (e.g. for USB device mode) or if USB support is not required.
+otg_mode=1
+
+[all]
+
+[pi4]
+dtoverlay=vc4-fkms-v3d
+# Run as fast as firmware / board allows
+arm_boost=1
+
+[all]
+
+####################################################
+####     MainsailOS specific configurations     ####
+####################################################
+####      DO NOT CHANGE SECTION BELOW !!!       ####
+####   UNLESS YOU KNOW WHAT YOU ARE DOING !!!   ####
+####################################################
+
+## For more options and information see
+## https://www.raspberrypi.com/documentation/computers/config_txt.html
+## Some settings may impact device functionality. See link above for details
+
+## For additional information about device filters see
+## https://www.raspberrypi.com/documentation/computers/config_txt.html#model-filters
+
+
+[pi0]
+## This affects Pi Zero(W) and Pi Zero2
+## Due lag of RAM, limit GPU RAM
+gpu_mem=256
+
+[pi2]
+gpu_mem=256
+
+[pi3]
+## Use 256 if 1Gb Ram Model!
+gpu_mem=256
+gpu_mem=256
+
+[pi4]
+dtoverlay=vc4-fkms-v3d
+## Do not use more than 256Mb on Pi Model 4, it uses its own Management.
+gpu_mem=256
+
+[all]
+
+## SPI Interface is enabled by default for Input Shaper
+## This colides with Hyperpixel Display!
+## Hyperpixel Screen uses the same Pin for Backlight.
+dtparam=spi=on
+
+
+## Enable Hardware UART for Serial Communication
+## This also disables Bluetooth!
+enable_uart=1
+dtoverlay=disable-bt
+
+## Enable I2C by default.
+## This is used by Klipper's Host MCU
+## See https://www.klipper3d.org/RPi_microcontroller.html#optional-enabling-i2c
+## for destails.
+## For MPU Accelrometer please use
+## dtparam=i2c_arm=on,i2c_arm_baudrate=400000
+dtparam=i2c_arm=on
+
+
+### EXPERIMENTAL - Enable 64bit Kernel
+### The 64-bit kernel will only work on:
+### Raspberry Pi 3, 3+, 4, 400, Zero 2 W and 2B rev 1.2
+### and Raspberry Pi Compute Modules 3, 3+ and 4.
+# arm_64bit=1
+
+####################################################
+
+[all]
+dtoverlay=w1-gpio